|Model RC12 (click options for RFQ)|
|Cable Connector Options||B||2B||B1||Bv1||Bv133||Bv2||Bv3||Bv4||BvF||Fv1||Fv2||Fv3|
Customized sensor tip, straight.
Custom Sensor Tip, Straight and Threaded, Standard Lengths
Custom Sensor Tip, Non-metallic, Peek or Torlon
Square body right angle tip, unthreaded.
Square body right angle tip, threaded.
Special tip made to customer specifications.
High Temperature Tip 250°C continuous; 350°C intermittent.
High Temperature Tip 350°C continuous; 450°C intermittent.
High Temperature Tip >480°C; quartz fibers.
Non-Magnetic Tip Brass or Aluminum.
Invar Tip for low CTE.
Side-viewing sensor tip.
Adds a sapphire window epoxied into the sensor tip.
Adds a sapphire window brazed to the sensor tip.
Jacket: Interlocking Stls Stl, crush proof, not liquid tight, widest temperature range.
Jacket: Silicone, very flexible, liquid tight, not crush proof, good to 200°C.
Jacket: Silicone over PTFE spiral wrap, semi-crush proof, short lengths only, good to 200°C.
Jacket: Corrugated Plastic, semi-crush proof, liquid tight, good to 85°C.
Jacket: PTFE over SS Interlok, crush proof with vapor barrier protection, good to 260°C.
Jacket: SS Interlok over PTFE, crush proof with vapor barrier protection, good to 260°C.
Jacket: PVC over nylon wrap, semi-crush proof, good to 105°C.
Jacket: PTFE tubing, MRI & EMF & Vacuum Compatible, Vapor Barrier, Cryogenic to 260°C.
Jacket: PVC, not crush-proof, good to 105°C.
Jacket: Semi-rigid Annealed SS tubing, good to 850°C.
Jacket: Silicone over SS Interlok, good to 200°C.
Jacket: Polyolefin Shrink Tubing, Thin wall moisture/vapor barrier, radiation resistant, not crush proof, good to 150°C.
Jacket: Polyolefin over SS Interlok, Thin wall moisture/vapor barrier, crush proof, good to 150°C.
Extra length of fiberoptic cable.
Connectorizes sensor system with in-line connector. (D6, RC12 n/a). *Option B is also required for use with vacuum passthru flanges & assemblies Bv1, Bv2, Bv3, Bv4, BvF, BvW.
Provides a 3 piece sensor system; amplifier, extension cable and probe.
Connectorizes sensor system with bulkhead connector (D6 n/a).
Connectorizes sensor system with single channel vacuum passthru hardware for 1 E-7 TORR (1 nPa). Includes ultra-torr compression fitting (D6, RC12 n/a) *Requires Option B.
Connectorizes Sensor System With Single Channel Vacuum Passthru Hardware Mounted in a 1.33" CF Flange, for 10 E-7 Torr (not available for D6, D12 or RC12) *Requires Option B.
2 port single channel high vacuum passthru flange for D models for 1 E-11 TORR (10 pPa) (D6 n/a) *Requires Option B
3 port single channel vacuum passthru flange for RC models for 1 E-11 TORR (10 pPa) (RC12 n/a) *Requires Option B.
4 port dual channel vacuum passthru flange for D modelsfor 10 E-11 TORR (D6 n/a) *Requires Option B
Multi-channel high vacuum passthru assembly for 1 E-7 TORR (1 pPa). Provides fused fiberoptic passthru and multi-channel vacuum flange assembly. Can accomodate 8 D type or 5 RC type sensors. (D6, RC12 & RC20 n/a) *Requires Option B.
Provides Temperature Stabilized Electronics For Low Drift and High Accuracy.
Digital Control with analog output.
Additional output, DC coupled with 10x gain and adjustable DC offset.
Additional output, AC coupled with 10x gain.
High frequency amplifier for D models up to 200 KHZ bandwidth.
High frequency amplifier for D models above 200 KHZ to 1 MHZ bandwidth.
Provides RC models with a high bandwidth amplifier, DC - 200 KHz. Bandwidths up to 350 KHz can be specified.
Additional output for D models with bandwidths up to 200 KHZ.
Additional output for D models with bandwidths exceeding 200 KHz up to 1 MHz.
Adds an additional high frequency output.
Low frequency amplifier (< 20 KHz), 100 Hz STD.
Additional output with low frequency bandwidth (< 20 KHz), 100 Hz STD.
Digital display - DC volts.
Low Noise Amplifier - The amplifier is optimized to operate with highly reflective targets only. This cuts noise floor in half, thereby doubling resolution.
Provides an adjustable 0 to -4 VDC offset control. This feature is used to eliminate the DC offset from the sensor output, thereby increasing readout resolution.
Polynomial Curve Fit For Operation In Non-Linear Ranges.
Connectorized AC/DC power adaptor and BNC output.
Ambient Light Rejection for 850 nm LED.
Blue Light Sensor, 470 nm.
Visible red Light Sensor, 624 nm.
Provides Sensor Amplifiers with 0 - 10 Volt Analog Output.
Additional Output with Linear Range Spanning 0 - 5 volts.
A 19 inch rack mount enclosure for powering and controlling up to 5 RS232 DMS sensor channels. It operates on AC power and is controlled via RS232 communication. Any combination of D and RC models can be mixed in the rack. Price includes RS232 cable, LabView drivers and Philtec DMS Control Software.
A 19 inch rack mount enclosure for powering and controlling up to 10 RS232 DMS sensor channels. It operates on AC power and is controlled via RS232 communication. Any combination of D and RC models can be mixed in the rack. Price includes RS232 cable, LabView drivers and Philtec DMS Control Software.